The Tile Doctor Natural Sealer is a solvent based, no-sheen impregnating sealer formulated for protection of the natural character and appearance of unsealed surfaces and natural stone. It contains built in stain protection and durability perfect for professional installations. The layer of protection forms a vapor permeable barrier that resists water, grease, oil, and dirt.
The formula is non-yellowing and is weather resistant. May also be used as a pre-grout sealer and for sealing grout joints.
400-1500 square feet per gallon per coat. Coverage will vary depending on type of stone, porosity and texture of surface absorption, temperature, humidity and method of application.
||1 Pint (473 mL)
||1 Quart (946 mL)
||1 Gallon (3.8 L)
Use on interior/exterior natural stone, marble, granite, limestone, brick, slate, saltillo, unglazed tile, grout and masonry surfaces. Works on most porous architectural substrates.
Read entire label before using. Surface must be clean, dry and free of existing sealers or coatings. Allow at least 48 hours after new installations before sealing. Apply and saturate surfaces using a paint brush, paint roller, paint pad/applicator, clean towel or low pressure sprayer with no more than 25 psi. Note: Do NOT Aerosolize. Be sure that any sealer that does not penetrate surface is polished off surface within 5 minutes of application using absorbent paper or cotton towels. If 2 or more coats are applied, allow a minimum of 2 hours drying time between coats. Achieves full cure in 48 hours. Some highly porous surfaces may require an additional coat after full cure. Clean applicator tools with mineral spirits after each use.
GROUT RELEASE APPLICATION: For new installations, follow application procedure above. Allow to cure a minimum of 2 hours before applying grout.
TEST A SMALL AREA according to application instructions with a 24-hour cure time to determine desired results. Test for stain repellency using likely contaminants.
The Tile Doctor Advanced Tile and Stone Cleaner is recommended for surface cleaning.
HANDLING AND STORAGE
Close container tightly after each use. Store in original container in a cool, dry area. Freeze/thaw resistant. Dispose of residue or any unused leftover product in accordance with applicable federal, state, and local requirements.
Do not allow sealer to come in contact with any non-recommended surface as product is not completely removable. Sealers and finishes should not be used before or after use of Natural Sealer. If Natural Sealer is not WIPED COMPLETELY DRY within 5 minutes, a residue may form. If residue occurs, use a scrub brush with alcohol to remove. Sealer will not prevent surface wear or protect from acids or caustic chemicals.
COMBUSTIBLE Keep away from heat, sparks and open flame. Caution: use in well-ventilated areas. Do not use this product with high pressure sprayers. Use low pressure sprayers with no more than 25 psi. Do not aerosolize. Avoid prolonged skin contact. Rubber gloves and eye protection should be worn during application. IF INGESTED: if person is conscious, immediately give 2 glasses of water. Do not induce vomiting. Seek medical attention. EYE CONTACT: Flush with water. If irritation persists, seek medical attention. SKIN CONTACT: Wash immediately with soap and water. If irritation persists, seek medical attention. INHALATION: relocate to fresh air. If symptoms persist, seek medical attention. For technical assistance or more information, please call 877-290-9015 Monday through Friday 8:00 a.m. to 5:30 p.m. Eastern Time. For chemical emergency ONLY (spill, leak, fire, exposure or accident), call CHEMTREC at 800-424-9300. KEEP OUT OF REACH OF CHILDREN AND PETS.
Will vary depending on hardness and texture of surface, type of area, surface wear, frequency and type of maintenance products used. The expected wear is up to 10 years. Exterior applications may require more frequent reapplication. Weather condition, harsh cleaning methods, and high alkaline, acidic or solvent-based cleaners will affect wear.